Fundamental Plumber Tips for Bathtub Installation
Fundamental Plumber Tips for Bathtub Installation
Blog Article
Are you currently looking for info around How to Install a Bathtub Yourself?
Setting up a tub isn't exactly brain surgery, but it does call for strong plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is easily easily accessible, the job can move rapidly; if you have to open a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the job as well as are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will aid you install a new bath tub in your bathroom if you have currently bought a new tub and don't need to alter the setup of your previous supply of water pipelines.
Your devices and also product checklist must make up the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the restricted gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been removed, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to moving on to fit the new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bathtub up until the level reviews level.
To mount faucets, fit the bottom of the outermost flexible tap port to the proper supply pipe by making a compression join; then do the very same for the other tap.
Switch on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been made use of at the very least once as this will certainly settle it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Safeguard the tap in place with the producer given backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous kind should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, bring about difficulties with wetness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry on Tools You Need to Install a New Bathtub when doing a search on the search engines. Appreciated our entry? Please share it. Help somebody else discover it. Thank you so much for your time spent reading it.
Need it done? Dial! Report this page